歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-常見問題

常見問題

通過式清洗機的操作事項與停機事項

作者：admin來源：http://www.yuehaihotel.com.cn/時間：2022-12-09

通過式清洗機是一種新型的節能的清洗設備，在工業清洗領域的應用目前十分廣泛，下面來講講通過式清洗機的操作事項與停機事項。

The through washer is a new type of energy-saving cleaning equipment, which is widely used in the field of industrial cleaning. Now let's talk about the operation and shutdown of the through washer.

操作事項

Operational matters

1工作前先檢查清洗液的配方濃度和配方比例是否合適，水箱液面高度是否夠。

1 Before working, check whether the formula concentration and proportion of the cleaning solution are appropriate, and whether the liquid level of the water tank is high enough.

2分別調定清洗液箱和漂洗液箱的電接點溫度計為50一60度。

2 Set the electric contact thermometer of the cleaning solution tank and the rinsing solution tank to 50-60 degrees respectively.

3用鑰匙將電源控制開關，置于開位置。

3 Use the key to turn the power control switch to the ON position.

4開啟加熱器，使其開始自動加溫。

4 Turn on the heater to start automatic heating.

5開啟浮油排除裝置開始浮油排除，因此式水泵未開啟，水面平靜，排油效果好。

5 Open the oil slick discharge device to discharge the oil slick, so the water pump is not opened, the water surface is calm, and the oil discharge effect is good.

6等溫度升到預定值后即開始工作，操作者根據需要選擇開關，按每個單動按鈕，使水泵，吸霧，輸送等全部動作。

6 When the temperature rises to the preset value, the operation will start. The operator can select the switch as required and press each single action button to make the water pump, fog suction, transportation, etc. all act.
通過式清洗機

7當機器運行后，操作工人便可以在裝料口不斷地把零件裝載輸送網帶，清洗，漂洗，吹干，輸出，在卸料口取下清洗好的零件。

7 When the machine is running, the operator can continuously load the parts into the conveyor belt at the loading port, wash, rinse, blow dry, and output, and then take down the cleaned parts at the unloading port.

停機事項

Shutdown matters

1清洗工作結束后，當后一個零件取下，按停止按鈕，全機停止。

1 After cleaning, when the last part is removed, press the stop button to stop the whole machine.

2清洗液應定期添加自來水和一定比例的金屬清洗液以補充消耗，使液面保持在一定高度，如果清洗效果達不到工藝要求時，應全部更換清洗液。

2 The cleaning solution shall be replenished with tap water and a certain proportion of metal cleaning solution regularly to maintain the liquid level at a certain height. If the cleaning effect cannot meet the process requirements, the cleaning solution shall be replaced completely.

3清理設備污垢后，關閉電源。

3 After cleaning the equipment, turn off the power.

此外要記得及時添加清洗劑或更換清洗液、漂洗液。定期檢查自來水供應情況，按液位計指示，及時添加滿水。等等。更多相關內容事項就來我們網站www.yuehaihotel.com.cn進行咨詢了解吧！

In addition, remember to add detergent or replace detergent and rinsing solution in time. Regularly check the supply of tap water, and timely add full water as indicated by the level gauge. wait. For more information, please visit our website www.yuehaihotel.com.cn!

上一篇：碳氫清洗機清洗時的九個要點注意
下一篇：超聲波清洗機的脫氣功能有什么用