歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-新聞資訊

新聞資訊

通過式清洗機的工作流程介紹

作者：admin來源：http://www.yuehaihotel.com.cn/時間：2022-08-09

通過式清洗機的工作流程是怎樣的呢？下面山東超聲波清洗機廠家為您講講這個問題，讓您在使用該設備的時候不出什么問題。

What is the working process of the pass through cleaner? Next, Shandong ultrasonic cleaning machine manufacturer will tell you about this problem so that you can use this equipment without any problems.

1、檢查清洗液在工作前的濃度和配比，水位是否足夠高。

1. Check the concentration and proportion of cleaning solution before operation and whether the water level is high enough.

2、打開水箱和水泵之間的兩個閘閥。

2. Open the two gate valves between the water tank and the water pump.

3、將洗滌罐和沖洗水箱的電接觸溫度計分別設置為50～60度。

3. The electric contact thermometers of the washing tank and the washing water tank are set at 50 to 60 degrees, respectively.

4、把電源控制開關和鑰匙放在打開的位置。

4. Put the power control switch and key in the on position.

5、連接外部蒸汽加熱，調節T1和T2溫控表。

5. Connect external steam heating and adjust T1 and T2 temperature control meters.

6、打開加熱器，使其開始自動加熱。

6. Turn on the heater to start automatic heating.

7、打開除油裝置，開始除油，因此水泵不打開，水面平靜，排油效果好。

7. Open the oil removal device to start oil removal. Therefore, the water pump does not open, the water surface is calm, and the oil discharge effect is good.

8、當溫度上升到預定值時，操作者開始工作，操作者根據需要選擇開關。根據每個單動按鈕，進行泵、霧、運輸等。

8. When the temperature rises to a predetermined value, the operator starts to work, and the operator selects the switch as required. Pump, fog, transport, etc. according to each single action button.
山東超聲波清洗機

當機器運行時，操作者可連續地將輸送帶裝入裝載口，沖洗、漂洗、吹干和輸出，并在卸貨港移除清潔部件。

When the machine is running, the operator can continuously load the conveyor belt into the loading port, wash, rinse, blow dry and output, and remove the cleaning parts at the unloading port.

通過式清洗機認真維護保養是保持設備良好性能和延長使用壽命的保證。維護保養分為日常保養和定期維護保養兩種，日常保養的內容有：

Careful maintenance of the through type cleaning machine is the guarantee to maintain the good performance of the equipment and prolong the service life. Maintenance is divided into daily maintenance and regular maintenance. The contents of daily maintenance include:

開機前要檢查潤滑油是否充足，要檢查各個連接零部件是否連接緊密，要檢查過濾網是否干凈等。高壓清洗任務完成后，要排放干凈機器設備內的殘留水，擦拭干凈機器，收納好進水管和出水管，把設備放置在通風干燥的地方。

Before startup, check whether the lubricating oil is sufficient, whether the connecting parts are tightly connected, and whether the filter screen is clean. After the high-pressure cleaning task is completed, the residual water in the machine and equipment shall be drained, the machine shall be wiped, the water inlet and outlet pipes shall be stored, and the equipment shall be placed in a ventilated and dry place.

通過式清洗機還要定期維護保養，定期更換機油，通常在運轉200小時后，更換新的機油，防止舊機油潤滑效果差磨損機器。定期檢查密封圈是否老化，及時更換新的密封圈，保持設備良好的密封性。

The through type cleaning machine shall also be regularly maintained and the engine oil shall be replaced regularly. Usually, after 200 hours of operation, the new engine oil shall be replaced to prevent the old engine oil from wearing the machine with poor lubrication effect. Regularly check whether the sealing ring is aging, and replace the new sealing ring in time to maintain good sealing performance of the equipment.

正確操作使用才能防止故障，長期保持良好性能，發揮設備的作用。所以以上的工作流程等內容要充分了解到才，更多事項就來我們網站www.yuehaihotel.com.cn咨詢吧。

Correct operation and use can prevent failure, maintain good performance for a long time, and play the role of the equipment. Therefore, you should fully understand the above workflow and other contents. For more information, please visit our website www.yuehaihotel.com.cn.

上一篇：超聲波清洗機使用期要注意控制各因素
下一篇：噴淋清洗機檢查有哪些關鍵點？